17 precautions for daily construction and maintenance of road rollers



You are here: Our news > 17 precautions for daily construction and maintenance of road rollers

2022-07-07 17 precautions for daily construction and maintenance of road rollers

Read: 6028

share Copy page link
share Share link to: Facebook | Twitter
Precautions for daily construction and maintenance of road rollers

1. Before working, check the parts, pipelines, screws, belts, lights and three fluids according to the maintenance content,
check the sprinkler system with double steel wheels, check the chain and tire pressure on the rubber wheels, etc.

2. Don't wear sandals, slippers and shorts to work to avoid accidental burns or bruises.

3. Before starting, check whether there are no obstacles and potential safety hazards around the machine, notify people near the machine to get out of the way, put the handle in the neutral position, and sound the whistle three times to warn.

4. When starting, if the engine cannot be started within 15 seconds, it should be stopped for half a minute and then restarted.
If it fails to start for 3 consecutive times, the reason should be checked and the fault removed before starting.

5. After starting, the engine needs to idle for a while, wait for the water temperature to reach about 50 degrees before driving, and the same is true when turning off the engine, and then turn off the engine after idling for a few minutes.

6. The road roller should pay attention to check the cleanliness of the wheels before rolling the road.

7. When the road roller is operating, it should keep driving in a straight line as much as possible. It is not allowed to brake suddenly on the uncompacted road surface. Extend the length of the pressed road surface as much as possible, avoid excessive steering, and prohibit steering and sharp turns in situ.

8. The steel wheel cannot vibrate on the spot while walking. It must start and then vibrate. When stopping, it must first stop and then stop.

9. During the running process of the road roller, the reversing or shifting must be stopped after the machine is stopped.

10. When the water is stable when the rubber roller is rolling, it is judged whether it needs to be supplemented and rolling according to the site conditions.

11. When working on a ramp, the speed should be lowered as much as possible, and it is forbidden to drive on a cross slope greater than 20%.

12. When working with multiple rollers, the vertical distance should be kept more than 3 meters, and the horizontal distance can be between 0.5 and 1 meters.

13. It is strictly forbidden to use the roller to pull other equipment.

14. When the machine needs to stop for a long time after compaction, it should be stopped as far back as possible and parked on the lower side of the road in the longitudinal direction, and cannot be parked in a row horizontally.

15. Traffic rules should be obeyed when transitioning. The steel wheel must drive at a low speed when encountering a hard road surface. When the distance is too long, a scooter should be used for consignment.

16. After the machine is stopped, it should be parked on a flat and solid ground. It cannot be parked on the edge of the roadbed. If it needs to be parked on a ramp, it should be plugged with stones or wood blocks under the wheels, and reflective cones should be placed.

17. When the roller is parked for a long time, it should be cleaned and maintained regularly, the battery should be removed, the roller should be fixed, and rainproof measures should be taken.


Please see more »
17 precautions for daily construction and maintenance of road rollers


17 precautions for daily construction and maintenance of road rollers




Get more information from us

* Please enter your message in the box below:
(* denotes a mandatory field)


Title: *
Name: *
Company: *
Country: *
City*:
Phone
(WhatsApp)Number:
E-Mail: *


Please write the result *

WHY CHOOSE US

OVER 15 YEARS OF SUCCESSFUL SALES ON THE GLOBAL MARKET. THE BEST SELECTION FROM THE MOST RELIABLE MANUFACTURERS.
DIRECT DELIVERY FROM MANUFACTURERS FACTORIES, NO WAITING AND MINIMUM PRICE



MULTIPLE CATEGORY
More than 120 different categories for you to choose from

LARGE STOCK
More than 30,000 vehicles and equipment are waiting for you to stock for immediate delivery

FAST SHIPPING
Fast shipping time to any country in the world. Door to door service is available for each way.

oDM/OEM
Any factory modification to your requirements. Including your logo and/or Pantone colour of choice.

WARRANTY
1-3 year warranty and lifetime technical service and spare parts

CUSTOMIZED SERVICE
Technical Support and friendly service 24/7

ARMY-UK.COM ® latest arrivals

NEW MACHINERY® the best offers

ARMY-UK.COM ® the best construction vehicles

ARMY-UK.COM ® the best UTV and ATV vehicles

ARMY-UK.COM ® military gear and vehicles with promotional price

NEW MACHINERY® LATEST NEWS


Crazy Engineering Days Sale
Submit Form to Get Order Discount and $5,000 Off Coupon
Separated DTH Surface Drill Rig HW-916 is a trusted machine for mining and construction companies and contractors engaged
in presplitting and conventional production blasthole drilling.
Drilling diameter (mm) φ90-127 , Maximum torque (Nm 1950

  READ MORE  
English - Deutsche - French - Dutch - Portuguese - Spanish - Italian - Chinese - Korea - Japan - turkish - Arabic - thai - vietnamese - Hindi - Hindi


Manufacturers: BYD | BMW | BAUDOUIN | DOOSSAN | DONFENG | DEUTZ | SINOTRUK | GAC | HASDER| HAITAI| HENGWANG CATERPILLAR | CUMMINS | CXXM | MAN | JCB | PERKINS | VOLVO | VOLKSWAGEN | SHANTUI | SIHAO | SHACMAN| STAMFORD | WEICHAI | LOVOL | XCMG | TOPMAC | ZOOMLION | FOTON | FOTMA | TAIGUO | TESLA| YTO | JINMA | sitemap.xml for Google

  My Cart


Save any items in your bag and when you're ready, just order.
CLICK HERE